Wolverine W4.5 Temro Oil Pan Tank Heater kit 50 Watt 1.25"x3.5" Pad Heat

Description

Phillips Temro
3400060
50 Watt Wolverine
4.5
heating pad, 110 Volt AC.
Phillips Temro recently purchased Wolverine heaters and is now selling them under their name.  Same great heaters.
This auction is for a Pan or Tank mounted heater.
The heater is attached directly to the pan or tank with a special 3M adhesive.
This heater is significantly more efficient and better than a conventional tank heater.
This heater is perfect for smaller applications such as:
ATV’s
Snow blowers
Golf Carts
Generators
Motorcycles
Lawn Tractors
Air Compressors
4 cycle Snowmobiles
A conventional tank heater does a great job heating the water in your engine. But does nothing to warm the oil. Cold oil takes time to start flowing when you start your vehicle. Until the oil flows, you are wearing out your engine. This heater keeps the oil warm and flowing no matter the outside temperature.
Faster/easier engine cranking in cold weather
Helps reduce engine wear with easy flow of engine oil
Immediate engine oil pressure
Easy installation
Most efficient means of heat transfer available
No cutting hoses, removing frost plugs, or loss of anti-freeze
Each model thermally balanced to meet your needs
No danger of oil carbonization
Permanent. Once applied, unit need not be removed
This heater will more than pays for itself in reduced electrical usage
1.25" x 3.5"
3400060
Kit comes complete with Heating Pad, Bundle Ties and Sealant.
Hydraulic Fluid, Oil and Biofuel Heaters
Heater
Oil
Hydraulic
Fluid
Output
Watts
Amps
Volts
Pad
Length
Pad
Height
Pad
Width
Cord
Length
4.5
1–3 qt.
≤ 1 gal.
50
0.4
120
3½"
1
⁄
8
"
1¼"
6′
9.0
3–6 qt.
1–7 gal.
125
1.0 / .52
120 or 240
3"
1
⁄
8
"
3"
6′
9.1
3–6 qt.
1–7 gal.
125
1.0 / .52
120 or 240
1½"
1
⁄
8
"
6"
6′
16
5–13 qt.
6–16 gal.
250
2.2 / .96
120 or 240
4½"
1
⁄
8
"
3½"
6′
M25
5–13 qt.
6–16 gal.
250
2 / 1
120 or 240
6¾"
1
⁄
8
"
2¾"
6′
40
13–27 qt.
16–32 gal.
500
4.6 / 2.08
120 or 240
5"
1
⁄
8
"
7"
6′
80
26–48 qt.
31–58 gal.
1000
8.4 / 4.17
120 or 240
6"
1
⁄
8
"
11¾"
6′
M1250
12–40 gal.
58–192 gal.
1250
10.4 / 5.2
120 or 240
14½"
1
⁄
8
"
8½"
6′
12V50W3x3
1–5 qt.
50
4.1
12
3"
1
⁄
8
"
3"
2′
RTH-60
1–4 gal.
60
.5 / .25
120 or 240
8½"
1
⁄
8
"
5½"
6′
12V125W4X4
2–3 gal.
125
10.4
12
4"
1
⁄
8
"
4"
2′
12V250W5X5
3–5 gal.
250
20.8
12
5"
1
⁄
8
"
5"
2′
Diesel Fuel Filter and Battery Heaters
Heater
Diesel
Fuel
Battery
Output
Watts
Amps
Volts
Pad
Length
Pad
Height
Pad
Width
Cord
Length
BH-60
•
60
.5 / .25
120 or 240
8½"
1
⁄
8
"
5½"
6′
FH-50W-12V
•
50
4.1
12
9"
1
⁄
8
"
3"
2′
FH-100W-12V
•
100
8.3
12
12"
1
⁄
8
"
4"
2′
FH-40-120V
•
40
0.3
120
8"
1
⁄
8
"
2¼"
6′
FH-100W-120V
•
100
0.8
120
12"
1
⁄
8
"
4"
6′
International Use — CSA/CE Certified
Hydraulic Fluid, Oil and Biofuel Heaters
Heater
Oil
Hydraulic Fluid
Output
Watts
Amps
Volts
Pad
Length
Pad
Height
Pad
Width
Cord
Length
4.5CSACE
1–3 L
≤ 4 L
50
0.4
120
8.89 cm
2.54 cm
3.18 cm
1.83 m
9.0CSACE
3–6 L
14–26 L
125
1.0 / .52
120 or 240
7.62 cm
2.54 cm
7.62 cm
1.83 m
9.1CSACE
3–6 L
14–26 L
125
1.0 / .52
120 or 240
3.81 cm
2.54 cm
15.24 cm
1.83 m
16CSACE
5–14 L
23–59 L
250
2.2 / .96
120 or 240
11.43 cm
2.54 cm
8.89 cm
1.83 m
40CSACE
13–29 L
59–123 L
500
4.6 / 2.08
120 or 240
12.7 cm
2.54 cm
17.78 cm
1.83 m
80CSACE
27–51 L
118–218 L
1000
8.4 / 4.17
120 or 240
15.24 cm
2.54 cm
29.85 cm
1.83 m
12V50W3x3
Up to 5 L
50
4.1
12
7.62 cm
2.54 cm
7.68 cm
.6 m
12V125W4X4
8–11 L
125
10.4
12
10.16 cm
2.54 cm
10.16 cm
.6 m
12V250W5X5
11–19 L
250
20.8
12
12.7 cm
2.54 cm
12.7 cm
.6 m
Diesel Fuel Filter and Battery Heaters
Heater
Diesel
Fuel
Battery
Output
Watts
Amps
Volts
Pad
Length
Pad
Height
Pad
Width
Cord
Length
FH-50W-12V
•
50
4.1
12
22.86 cm
3.17 mm
7.62 cm
.6 m
FH-100W-12V
•
100
8.3
12
30.48 cm
3.17 mm
10.16 cm
.6 m
BH-60CSACE
•
60
.5 / .25
120 or 240
21.59 cm
2.54 cm
13.97
1.83 m
This heater can
only
be used on a metal pan or tank. It should never be installed on a plastic, poly or non-metallic container.
We also sell a line of Thermostat controlled outlets
TC-1 Turns ON at  0 degree F  and OFF at 10 degree F    Listing
320300526521
TC-2 Turns ON at  20 degree F  and OFF at 30 degree F    Listing
320300525834
TC-3 Turns ON at  35 degree F  and OFF at 45 degree F    Listing
320300528585
Professional grade jumper cables on our listing
320305647039
BEFORE INSTALLATION
THE INSTALLATION AREA MUST BE:
Metal surface – Steel, Aluminum, Cast Iron, etc. (Not all oil pans are metal).
Flat – The Wolverine Preheater must have a smooth installation surface area. The Wolverine Preheater must have a solid contact with the oil pan surface.
Smooth – No bumps, ridges, ribs, fins, indentations, grooves, holes or part numbers can be allowed in the installation area.
Clean – Remove all paint, dirt, grease and oil from the installation area.
Warmed – Operate engine as needed to raise oil pan temperature. A pan surface temperature of 100°F (38°C) or more is recommended. If so equipped, refer to the engine oil temperature gauge.
INSTALLATION INSTRUCTIONS
1. Clean the selected installation area to remove any dirt, grease or oil - a pressure washer works great for this.
2. Grind or sand all paint from the surface area slightly larger than the heater. Do not polish this surface. A coarsely scratched surface is best.
HEATER MUST BE PLACED ON METAL SURFACE.
3. Use acetone, lacquer thinner or similar agent to wipe the area clean. If these recommended cleaners are not available a strong detergent scrubbing followed by a thorough fresh water rinse and towel dry will do. The surface must be absolutely clean.
DO NOT USE Gasoline • Solvents • Spray Penetrants • Diesel Fuel • Any product that leaves oily film
DO NOT CUT, TRIM or BEND HEATER!
4. Remove the protective covering from the pressure sensitive adhesive.
AVOID TOUCHING THE ADHESIVE.
Decide which direction you want the cord to go. Plug in the pad for
3 to 5 SECONDS (NO LONGER THAN 5 SECONDS)
to warm the adhesive.
WARNING: The pad will become very hot if plugged in longer and may burn exposed skin or damage heater. Unplug pad before applying to metal surface.
5. Place the edge opposite the cord on the clean surface. With a squeegee (supplied in kit) apply maximum pressure as you affix the pad. Carefully avoid wrinkles or creases; smooth the entire pad to the surface.
6. Attach the first length of AC cord with a cord tie. (supplied in kit). This prevents the weight of the cord from pulling down on the pad.
7. Plug the heater in for 5 to 10 SECONDS, unplug and squeegee the pad again. DO THIS TWICE!
8. Apply a small bead of high temperature silicone adhesive (supplied in kit) around the outside edge of the heating pad. DO NOT force the silicone under the pad. It is important to seal the entire perimeter of the pad for weatherproofing.
DO NOT USE ANY OTHER ADHESIVES TO APPLY PAD TO METAL SURFACE!
9. Route and secure the rest of the AC cord to a convenient location, such as through the grille. Avoid any moving or high temperature parts. Position the power cord so it is held snugly against the oil pan. Plastic ties are provided for use in securing/routing the power cord.
10. Keep all NON-METAL surfaces such as plastic oil pan covers, noise suppressors, rock guards, fiberglass shrouds etc away from pad  to avoid melting, warping or fire hazard.
AFTER INSTALLATION
DO NOT USE THE HEATER FOR 24 HOURS AFTER INSTALLATION. THE ADHESIVE BOND STRENGTH WILL DOUBLE IN 24 HOURS IF NOT USED.  THE HEATER CAN NOT BE REMOVED AND RE-INSTALLED ON A DIFFERENT PAN.
We combine shipping on multiple orders completed at the same time. If you are buying from our other listings, please complete your purchases at the same time. But do not pay for them. We will send you a PayPal invoice for the total with the correct discounted shipping.
.
See our other listings for 75, 125, 250, 500 and 1000 Watt Heaters